Intuitive Atmospheric Entry

Intuitive Atmospheric Entry is a common complaint on the Orbiter message boards that the aerodynamics on the Space Shuttle model are screwed up. This is usually reported after a person deorbits the vehicle, puts it in the right angle of attack... and then bounces off the atmosphere several times and overshoots the Cape. I know, I've done it myself. Here's how to enter the correct way.

Note: The aerodynamics of the stock Shuttle Atlantis which comes with Orbiter really are screwed up. It works great during launch, orbit, and the final gliding approach (Mach < 5.0), but in the hypersonic region it just doesn't work. I don't believe it is possible to do a good entry with it. I personally fly the Shuttle Fleet 3.9.2 myself, but I have heard many reports in the forum that the DeltaGlider III works also.

Deorbit Burn

The object of the deorbit burn is to put the vehicle into a new orbit which intersects the atmosphere. The deorbit burn must satisfy a number of constraints

• It must put the vehicle in the atmosphere
• It must hit a certain distance/altitude window
• It must hit a certain sink rate target
• It must use a minimum amount of fuel, to save fuel for the mission before and the entry after.

These are pretty easy constraints.

Basically this has to be done by trial and error, to find the correct deorbit profile for each spacecraft and orbit. For a Space Shuttle, get it down to a circular orbit with an altitude of around 225km. Then, wait until the orbit track passes "close enough" to the target base. It doesn't even have to be all that close, since the space shuttle has a large crossrange capability. Next, wait until the distance to the target is 18000km and dropping. At this point, do a retrograde burn until the perigee altitude is -20km. This will result in an entry interface at about 4400 nautical miles (8000km) from the target, at 400,000 feet (121.920km), with an appropriate sink rate.

You will notice on the map MFD that the ground impact point is well short of the target, but don't worry. We will be flying there, not falling.

Coast to Entry Interface (EI)

Make sure that before entry interface, the vehicle is buttoned up (doors closed, gear up, etc) and prepared for entry. The space shuttle really buttons up several orbits before the deorbit burn, but they have mission control and checklists and such to remind them of stuff. If you are riding inside the vehicle, it isn't obvious if the doors are hanging open, so jump outside with F1 and have a look. Then, maneuver to the correct angle of attack.

Entry Interface (EI)

Once the vehicle intersects the atmosphere, it starts flying, and two-body keplerian motion is over. This point is called Entry Interface, or EI for short. For traditional reasons since the Apollo program, EI has been defined as the point at which the vehicle crosses below 400,000 feet altitude. My experience in Orbiter is that the vehicle doesn't really start flying until it gets down to about 250,000 feet (80km). If you had time acceleration on, make sure to turn it off when the vehicle passes through 400kft, and turn on whatever reentry autopilot you want (Pro103 for the DeltaGlider, DAP (B key) for Space Shuttle 3.8+).

Angle of Attack (AoA)

Figure 1a. Shuttle flying at AoA of 17deg, at about mach 3. Higher mach numbers require a higher AoA

Figure 1b. Shuttle flying at AoA of 35deg, at mach 20

The Space Shuttle is a remarkably good aircraft, when travelling above Mach 5. Then again, you can fly a barn door if you get it going fast enough. Now, the bottom of the space shuttle is your heat shield, and it is covered with all those nice black tiles. Obviously we want that side towards the wind. The top is not shielded to the same extent. It is basically just a blanket to keep the swirling hot wind from below, off the vehicle. So, the shuttle was carefully designed to fly with a high angle of attack at high mach numbers.

When the spacecraft is flying, rather than falling, it relies on lift to keep it up. The amount of lift varies depending on the angle of attack. In the hypersonic range, the drag of a vehicle increases until the angle of attack reaches 90°. The lift also increases, but there is a certain maximum lift point, above which the lift will drop again. This maximum lift point depends on the shape of the vehicle and its speed, and is about 40° for the space shuttle from orbital speed down to about mach 10.

If you were unconstrained, you could reduce lift and control the glide slope by changing the angle of attack. BUT! You can't fly just any old angle of attack, since your heat shield is on the bottom. If you point the nose too much into the wind, you could do fun things like melt the windshield and stuff. Let's not do that.

Also, it is an interesting fact that within a large range, the higher the drag on an entering vehicle, the smaller the heat load the spacecraft has to deal with is. This is partly because the craft does a larger part of its braking high in the atmosphere where there is less air. So, we use a very high angle of attack all the way through the heat pulse, to increase drag, increase lift, and not melt the windshield.

The entry autopilot's job is to make sure that the spacecraft always has an appropriate angle of attack for your present speed. The shuttle DAP does a decent job of this, even though it always keeps the nose a little below the NASA standard. The Deltaglider III autopilot will set the angle of attack to whatever the pilot commands, but it does not automatically track the mach number.

Flying

So, if we can't change our lift by pitching up or down, what can we do? Here we get into something fun: The legalistic definition of lift is the aerodynamic force perpendicular to the direction of travel. It doesn't have to be up.

Figure 2. Flying level: Lift much greater than gravity

Figure 3. Flying rolled: Vertical lift equal to gravity

If you fly a reentry with the 40° angle of attack necessary from above, with the wings level, you will get so much lift that you will fly back up out of the atmosphere, into space. It will look like you bounced off the atmosphere. Since you did lose a bit of speed, you won't be in orbit anymore, and will eventually fall back down, but you will travel much farther downrange than you had intended, and will miss your landing. The Germans actually designed an aircraft, the Sänger Silverbird, which would glide all the way around the world, while never reaching orbital speed, and land back at its launch point. It skips eight times or more on its way around.

So, roll the spacecraft strongly. This is the most important part of the whole process. Understand this section, and these diagrams, and you are 90% of the way there.

The secret is that you roll, in order to only oppose gravity with a small component of lift, rather than all of it. For a conventional aircraft or winged entry vehicle, like the Shuttle, the lift vector is always perpendicular to the wings. Since you can control the wings, you can control the lift vector. So, roll the vehicle so that the vertical component becomes almost equal to the gravity vector. Now you are flying. You may have to roll close to 90° to get only the lift you need. Go ahead and do it, there is nothing to worry about as long as your AoA is correct and you have no sideslip, and the DAP and tail fin will take care of those things. Don't worry about the predicted impact point on the Map MFD. It doesn't know about flying. But, continue to pay attention to the Map MFD.

As you travel, you will decelerate constantly. At first, you are travelling at almost orbital speed, so there will be a strong "centrifugal force" component holding you up against gravity. (I know there's no such thing, but it is a convenient fiction at this point.) The combined gravity+centrifugal vector may be much less than the 9.8m/s^2 we are used to, more like less than 1m/s^2. So, you don't need very much vertical lift, and will roll over strongly. Once slower, the gravity vector will increase, and you will gradually need more and more lift to balance it. So roll less You can tell when you have rolled enough by looking at the Surface MFD. The vacc meter is precisely the difference between your lift vertical component and the current gravity+centrifugal vector. If the vacc is much less than zero, you are dropping too fast, and need more lift, so roll less, and get the tail closer to vertical. If the vacc is much greater than zero, you are flying back up, and need less lift, so roll more.

Sideslip

Figure 4. 40deg AOA, 78deg bank, 0deg sideslip

Figure 5. 40deg AOA, 73deg bank, large sideslip

While we want the pitch angle of attack to be large, and the bank to be whatever necessary to control lift, we want the yaw angle of attack, or sideslip angle, to be as small as possible. Basically we want the wind to hit the well-shielded nose dead on and slide along the side of the spacecraft, and not hit the relatively unprotected side of the ship dead on.

So, what does this look like? Some spacecraft have a sideslip angle meter. If yours does, great. If not, you can still get what you need from the orbit or surface HUD. Basically, all you have to do is keep the nose pointing vector exactly above the velocity vector. At high AoA, it is easier to see the arrow pointing towards the velocity vector. Just make sure this is down. Once you start lowering the nose and can see the velocity vector on screen, switch to the surface HUD.

If you are using either the DeltaGlider autopilot or Shuttle DAP, the autopilot will automatically take care of this for you. One more thing off your mind. If not, yaw towards the velocity vector and get it right under the nose.

Roll Reversal

Since you are rolled, you will have a large horizontal component to your lift vector. This necessarily will cause you to turn. Nothing can be done about this. You will turn. So, we get to what NASA calls a roll reversal. Let's say that in your initial deorbit, your orbit track is projected to pass to the right of the landing site. Roll left, and watch as your track slowly moves to the left, to the landing site, and then beyond it farther to the left. When it is far enough, roll back to the right.

If you are using the GPCMFD, its OPS3 has a nice display DELAZ, the delta azimuth to the target, or the number of degrees away from straight towards the target your velocity vector is. If this reads zero, you are moving straight towards the target. Notice that this has nothing to do with what direction your nose is facing. The GPC MFD also has a roll indicator. When the sign of the roll indicator and DELAZ are the same, DELAZ will be pushed towards zero.

When DELAZ reaches about 10deg (either positive or negative) you can roll the spacecraft the other way to get it to decrease towards zero again.

If you are just using the Map MFD, then use your judgement as to when the flight path is too far to one side or the other of the target.

Entry Profile

So, keeping in mind that you control the horizontal, and you control the vertical, you could fly around the upper atmosphere for as long as you want, losing basically no altitude. The only limiting factor is when you are no longer flying fast enough to lift, even when flying level. At this point you start sinking, down to the thicker atmosphere below. Still, keeping a zero sink speed until level, then holding level, maximizes glide time.

On a real spacecraft, this would eventually overheat the heat shield, which is of course a Bad Thing, but the shuttle and delta glider don't model this gradual overheating. The real problem with staying level is that it makes the final landing point hard to control. So, you need an entry profile. This is where all those rocket scientists earn their money, designing a profile which will simultaneously get the vehicle down, on target, without melting the heat shield, and without crushing the occupants or damaging the cargo. Fortunately NASA has published the entry profile for the shuttle in a form which is directly usable for an orbinaut.

Note that since Mach 1 is about 1kft/s, the airspeed column is also the approximate mach number column.

Range, NMi	Airspeed, kft/s	AoA deg	Alt, kft	Vert spd, ft/s	Left Roll deg	Right Roll deg
4472	25	40	400	--	--	--
2634	24	40	245	-46		R80
2158	23	40	237	-63		71
1801	22	40	231	-82		66
1522	21	40	225	-104	L63
1302	20	40	218	-121	60
1127	19	40	211	-142	61
978	18	40	205	-166	62
864	17	40	198	-184	63
766	16	40	191	-196	64
683	15	40	185	-119	64
615	14	40	181	-126	62
547	13	40	178	-136	59
481	12	40	173	-154	57
426	11	39	168	-195		R55
376	10	38	164	-174		46
327	9	36	158	-205		43
278	8	34	150	-237		40
230	7	30	141	-266		39
184	6	27	130	-272		40
141	5	23	117	-275		42
106	4	19	105	-263	L41
75	3	16	89	-248	40
61	2.5	14	82	-216
49	2	12	76	-282
37	1.5	9	65	-331
28	1	8	51	-263

• NMi = Nautical mile, 1NMi=1.851km
• kft = 1000 feet, 1000ft=304.8m
• ft=foot, 1ft=0.3048m

You can also use the following chart with speeds and distances converted to the metric system.

Range, km	Airspeed, m/s	AoA deg	Alt, km	Vert spd, m/s	Left Roll deg	Right Roll deg
8282	7620	40	122	--	--	--
4878	7315	40	75	-14		R80
3997	7010	40	72	-63		71
3335	6706	40	70	-62		66
2819	6401	40	69	-61	L63
2411	6096	40	66	-60	60
2087	5791	40	64	-59	61
1811	5486	40	62	-58	62
1600	5182	40	60	-57	63
1419	4877	40	58	-56	64
1265	4572	40	56	-55	64
1139	4267	40	55	-54	62
1013	3962	40	54	-53	59
891	3658	40	53	-52	57
789	3353	39	51	-51		R55
696	3048	38	50	-50		46
606	2743	36	48	-49		43
515	2438	34	46	-48		40
426	2134	30	43	-47		39
341	1829	27	40	-46		40
261	1524	23	36	-45		42
196	1219	19	32	-44	L41
139	914	16	27	-43	40
113	762	14	25	-42
91	610	12	23	-41
69	457	9	20	-40
52	305	8	16	-39

The most important thing is to have the correct altitude and airspeed for your distance from the target. Don't worry quite so much about vertical speed, just use it as a guideline to help you hit the altitude targets. Worry least of all about the roll. For one thing, this is for the real shuttle, and the Orbiter model doesn't have quite the same aerodynamic properties. Also, the roll reversals depend on exactly when and where you reenter at. Use whatever roll you need to get the sink rate you want, and roll reverse whenever you need to, to keep moving towards the target.

Summary

1. Maintain correct pitch angle of attack for your speed
2. Keep sideslip close to zero
3. Roll as necessary to keep your vertical speed appropriate for your speed and distance from the target
4. During entry, you will be spending most of your time looking at the Map MFD, Surface MFD, and cue card, checking that your sink rate and speed are appropriate for your distance from the target.
5. Don't forget to do roll reversals, to stay heading roughly towards the target.
6. Start flying like a normal airplane and begin to line up on the runway somewhere between mach 2 and 1

Precis

This article has a precis and appears in the Random addon or Random article section on the Main Page. The precis can be found at Intuitive Atmospheric Entry/precis and is displayed below.

Intuitive Atmospheric Reentry. It is a common complaint on the Orbiter message boards that the aerodynamics on the Space Shuttle model are screwed up. This is usually reported after a person deorbits the vehicle, puts it in the right angle of attack... and then bounces off the atmosphere several times and overshoots the Cape. I know, I've done it myself. Here's how to enter the correct way. (More...)